Sale

Unavailable

Sold Out

Proud Singapore Company Since 2015 - Worldwide free shipping for order over $70 !

LATEST mini motors THROTTLE 52V&60V for sale

LATEST mini motors THROTTLE 52V&60V for sale TIANTIAN LIFE

LATEST mini motors THROTTLE 52V&60V for sale

Regular price $78.00 Sale price $68.00
LATEST mini motors THROTTLE 52V&60V for sale

DT型LCD仪表(码表) 使用说明(通用)
尊敬的客户,欢迎使用本产品,为了您更好的使用,请仔细阅读使用说明。
1、外观图

2、按键
仪表上有二个按键,分别是电源和功能键。
3、使用
长按电源键开启电源。98%电池电量、速度是根据电动车运行状态瞬时显示,单次里程、累计里程等根据选择的功能显示。
仪表开机后,若长时间(3分钟)无速度信号输入,仪表会自动关闭电源。
短按功能键,变换仪表显示内容,分别有TIME,TRIP,ODO,VOL等字符出现,显示TIME时表示开机时间,显示TRIP时表示单次里程,显示ODO时表示累计里程,显示VOL时表示电池电压,单位伏特。
长按功能键,单次里程清零(在TRIP界面下)。
短按电源键,档位数字会闪烁,此时再按功能键会改变档位,1为慢速,2为中速,3为快速。
当电池电量低于10%时,仪表的背光会闪烁3次--亮10秒--闪烁3次循环;电池电量变成0%时,仪表的背光会不断闪烁提示必须要充电了。
仪表开机时,再次长按电源键关闭电源。
4、参数设置
当同时按下功能键和电源键时,进入仪表参数设置第一级菜单状态:
显示P0时,短按功能键,会显示P1,再短按功能键,会显示P2、P3、P4、P5、P6、P7、P8、P9、PA和PB;分别表示:P0为车轮直径设置;P1为电池电压设置;P2为磁极对数设置;P3为测速信号选择设置;P4为公里/英里选择设置;P5为非零起动和零起动选择设置;P6为有巡航和无巡航选择设置;P7为软起动和硬起动选择设置;P8为限速百分比设置;P9为电机扭矩设置;PA为电子刹车(EBS)设置;PB为LCD背光亮度设置。LCD右下方显示的参数即为对应的当前参数。需要改变参数时短按电源键,进入当前调整设置参数模式,LCD右下方显示的参数即开始闪烁,表示已经进入调整设置参数模式,可按功能键加一个量级,也可按电源键减一个量级。设置好正确的参数后,等待2-3秒,会自动退出到上一级菜单,此时并没有保存数据,需要等待5秒(或者再次同时按下功能键和电源键)退出设置模式才会保存之前设置的数据。
当显示P0时,短按电源键,进入电机轮径设置模式,LCD右下方显示的参数开始跳动,要改变车轮直径时(和后轮轮径设置一致显示的时速才会准确),可按功能键加0.5寸,也可按电源键减0.5寸,默认10.0,2-3秒后会自动退出到上一级菜单。
当显示P1时,短按电源键,进入电池电压选择模式;如显示52,表示车辆使用的电池为52伏;要改变电压值(设置的电压必须和车辆使用的电池匹配),调整方法同“P0”。默认使用60V电池。
当显示P2时,短按电源键,进入电机的磁极对数设置模式(设置的数据必须和车辆使用的后轮电机参数一直,时速显示才会准确),调整方法同“P0”。默认10。
当显示P3时,短按电源键,进入测速信号选择模式,调整方法同“P0”。当显示0时(一般都选择0),表示选择控制器内部信号测速,当显示1时,表示使用外接速度传感器信号。默认0。
当显示P4时,短按电源键,会进入公里/英里选择性模式,调整方法同“P0”。当显示0时,为公里,会显示Km/h;当显示1时,为英里,会显示Mp/h。默认0。
当显示P5时, 短按电源键,进入零起动和非零起动选择模式,调整方法同“P0”。当显示0时,表示零起动;当显示1时,LCD右上角会出现PAS,表示非零起动(助力起动)。默认0。
当显示P6时,短按电源键,进入有自动巡航和无巡航选择模式,调整方法同“P0”。当显示0时,表示无巡航;当显示1时,表示有8秒自动巡航,在正常骑行时,加速器稳定8秒就进入定速巡航状态,会出现符号“[→㈠←]”,要退出巡航只需触发刹车或者重新拨动加速器即可退出。默认0。
当显示P7时,短按电源键,进入硬起动和软起动选择模式,调整方法同“P0”。当显示0时,表示硬起动(起步时冲力大);当显示1-5时,表示1秒-5秒软起动(起步时柔和)。默认2。
当显示P8时,短按电源键,进入限速百分百控制模式,调整方法同“P0”。当显示1时,表示设定速度为最快速度的1%,显示2表示设定速度为最快速度的2%,以此类推,当显示100时,表示设定速度为最快速度。默认100。
当显示P9时,短按电源键,进入电机扭矩设置模式,调整方法同“P0”。当显示1时,表示扭矩为最大扭矩的50%,显示2时扭矩为最大扭矩的75%,显示3时扭矩为最大扭矩。默认2。
当显示PA时,短按电源键,进入EBS(电子刹车)强度选择模式,调整方法同“P0”。当显示0时,表示无EBS,当显示1时,表示EBS为最弱,当显示2时,表示EBS为略强,当显示5时,表示EBS为最强。默认1。
当显示PB时,短按电源键,进入LCD背光亮度调整模式,调整方法同“P0”。当显示0时,表示无背光,当显示1时,表示背光亮度为最弱,当显示2时,表示背光亮度略亮,当显示5时,表示背光亮度为最亮。默认3。

5、 故障显示
车辆出现故障时,仪表显示故障的部件,分别有刹车故障(在正常行驶时刹车也会出现此符号,属正常的刹车状态指示;如果在车辆出现问题时有此符号显示,表示刹车断电部分出现故障)、电机故障、转把故障、控制器故障等。这些故障指示只针对后电机控制器,前电机控制器出现故障没有提示。
仪表设置:

一.DT-II:
60V款【P0:10; P1:60; P2:10; P3:0; P4:0; P5:0; P6:0; P7:2; P8:100; P9:2; PA:1; PB:3】
二.DT-ULTRA:
60V款【P0:11; P1:60; P2:15; P3:0; P4:0; P5:0; P6:0; P7:2; P8:100; P9:2; PA:1; PB:3】
三. DT-RAPTOR:
60V款【P0:8; P1:60; P2:15; P3:0; P4:0; P5:0; P6:0; P7:2; P8:100; P9:2; PA:1; PB:3】
using
Press the power button on the power. 98% of the battery, an electric vehicle running speed based on the instantaneous state of display, a single mileage accumulated mileage and the like based on the selected function display.
After the meter is turned on, if a long time (3 min) Speed ​​input signal, the instrument will automatically turn off power.
Indicates that the battery is shorter press the function key, transforming the instrument display, respectively, TIME, TRIP, ODO, VOL and other character appears, the boot time display TIME, represents a single mileage display TRIP, indicate a total mileage display ODO, display VOL voltage in volts.
Press the function key, a single mileage cleared (in TRIP interface).
Short press the power button, the gear number will flash, then press the function key will change gears, one of slow, medium speed 2, 3 fast.
When the battery is below 10%, the instrument backlight will flash three times - bright 10 seconds - 3 cycles flashes; the battery power becomes 0%, the meter prompts backlight blinks continuously have to recharge.
When the meter is turned on, press the power button again to turn off the power.
4, parameter settings
When pressing the function key and a power key, a first parameter is set to enter the instrument level menu state:
Displaying P0, press the function key is displayed P1, and then press the function key is displayed P2, P3, P4, P5, P6, P7, P8, P9, PA and PB; respectively represent: P0 setting the wheel diameter; the battery voltage is set to P1; P2 is the number of pole pairs is provided; P3 is selected to set the speed signal; P4 is km / mile selected set; P5 nonzero and zero starting start setting selection; and P6 that there is no cruise cruise selection setting; P7 hard and soft start starting selection setting; P8 set to a percentage of the speed limit; LCD backlight brightness set to PB; P9 motor torque setting; PA to electronic braking (EBS). LCD is the parameter corresponding to the bottom right of the current parameter. Short press the power button, to enter the parameter setting mode to adjust the current required to change the parameters, the parameter LCD display starts blinking bottom right, that has entered the adjustment parameter setting mode, press the function key plus an order of magnitude, in accordance with a power button Save the order. After setting the correct parameters, wait for 2-3 seconds, will automatically exit to the previous menu, and at this time there is no save data, wait five seconds (or again press the function key and power key) will exit the setup mode save the data set before.
When displaying P0, press the power button, wheel diameter settings into the motor model, the bottom right of the LCD parameter starts beating, to change the diameter of the wheel (rear wheel diameter and speed setting will be displayed accurately consistent), can function key plus 0.5 inch, the power button can also be minus 0.5 inch, will automatically exit to the previous menu after default 10.0,2-3 seconds.
When the display P1, press the power button to enter the battery voltage selection mode; display 52, indicating that the battery of the vehicle used was 52 volts; to change the voltage value (the voltage must be set and the battery match vehicles), the adjustment method with " P0 ". Default 60V battery.
When the display P2, press the power button to enter (data to be provided and the rear wheel motor vehicle parameters have been used, the speed will be displayed accurately) set the number of poles of the machine mode, with the adjustment method "P0". 10 default.
When P3 is displayed, press the power button to enter the speed signal selection mode, with the adjustment method "P0". When 0 is displayed (usually select 0), the internal control signal indicating the selection speed, when the display 1, the external velocity sensor signal indication. Default 0.
When the display P4, press the power button, it will enter km / mile selective mode, with the adjustment method "P0". When the display 0, in kilometers, will appear Km / h; 1:00 when displayed in miles, displayed Mp / h. Default 0.
When the display P5, press the power button, to enter the zero and non-zero starting start selection mode, with the adjustment method "P0". 0 When the display indicates zero start; when the display 1, upper right corner of the LCD will be the PAS, it represents a non-zero start (start power). Default 0.
When the display P6, press the power button to enter the automatic cruise and non-cruise mode is selected, with the adjustment method "P0". When displaying 0, indicating no cruise; when the display 1, it indicates that the auto-cruise 8 seconds, during normal riding, the accelerator 8 seconds to enter a stable state cruise control, a symbol appears in "[→ i ←]", to exit cruise only trigger the brake or accelerator struck again to exit. Default 0.
When the display time P7, press the power button to enter the hard and soft start starting mode selection, adjustment method with "P0". When the display 0, represents a hard start (large momentum at the start); when the display 1-5, represents 1 to 5 seconds soft start (when the soft start). 2 default.
When the display P8, press the power button to enter hundred percent speed control mode, with the adjustment method "P0". When the display 1, represents the set speed of the fastest of 1%, 2 denotes a display setting fastest rate of 2%, and so on, when the display 100 shows the fastest speed is set. Default 100.
When the display P9, press the power button to enter the motor torque setting mode, with the adjustment method "P0". When the display 1, represents 50% of the maximum torque of the torque, the torque display 75% of the maximum torque of 2, 3 show the maximum torque torque. 2 default.
When displaying PA, press the power button to enter the EBS (electronic brake) intensity selection mode, with the adjustment method "P0". When displaying 0 indicates no EBS, when the display 1, EBS represents the weakest, when the display 2, showing EBS is slightly stronger, while the display indicates the strongest EBS. Default 1.
When PB is displayed, press the power button to enter the LCD backlight brightness adjustment mode, the adjustment method with "P0". When displaying 0 indicates no backlight, when the display 1, it indicates a backlight brightness of the weakest, when the display 2, represents a slightly brighter backlight brightness, when the display 5, the backlight brightness of the brightest expressed. Default 3.

5, fault display
When the vehicle fails, component failures instrument display, respectively, brake failure (this symbol will appear braking during normal driving, the normal brake state indication; This symbol display, indicates portions of the brake off issue occurs if the vehicle failure), the electrical fault, the fault turn, the controller failure. The fault indication for the motor controller, motor controller before failure occurs not only tips.


THANK YOU VERY MUCH

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Testimonials

Share blog posts, products, or promotions with your customers. Use this text to describe products, share details on availability and style, or as a space to display recent reviews or FAQs.

Author's name

Share blog posts, products, or promotions with your customers. Use this text to describe products, share details on availability and style, or as a space to display recent reviews or FAQs.

Author's name

Share blog posts, products, or promotions with your customers. Use this text to describe products, share details on availability and style, or as a space to display recent reviews or FAQs.

Author's name

Share blog posts, products, or promotions with your customers. Use this text to describe products, share details on availability and style, or as a space to display recent reviews or FAQs.

Author's name
30-Day Guarantee
2-Day Shipping
Fastest Respond
24/7 Support
Click to edit the product in Ali Orders.
Note: only show for shop owner